Products
Bykski 50mm Cylindrical Reservoir - White POM is a cylinder reservoir 50mm thick at the center. This reservoir has 4 ports allowing multiple configurations with one on the top and bottom and 2 on the side of the bottom cap.
Features
- Precision Cut POM Material
- Crystal Clear Tube
Specifications
- Material: White POM / Clear PMMA
- Length: 200mm
- Tube Width: 50mm
- Overall Width: 56mm
- Ports: 4
- Thread:G 1/4in.
Included Parts
- 1x 200mm Cylindrical Reservoir
- 2x Mounting Brackets - Black
- 2x Mounting Clip Brackets - Clear
- 2x Stop Fittings
- Mounting Hardware
Compatibility
Please be aware that the recessed fitting ports on the sides of the reservoir POM bodies will not accept Revolver fittings without using an extension or adapter first due to size constraints.
Warnings
*Not responsible for any hardware damage. Use at your own risk.
This full coverage block directly cools the video cards core (GPU), graphics memory (RAM), and voltage regulator modules (VRM). By directly cooling these components, you can achieve great temperatures and reach higher overclocks or extend the overall lifespan of your card by running at below-factory temperatures.
The block is constructed of high-purity copper that is nickel electroplated to prevent oxidation. A high-flow design is used to allow multiple blocks to run in series. Top and bottom ports can be used to configure parallel or serial designs in multi-block setups.
Specifications
- Block Material: Nickel Electroplated High Purity Copper / Acrylic
- Backplate Material: Black Anodized Aluminum (not in contact with coolant)
Compatibility
- (Including but not limited to the following models)
- Compatible with ASUS TUF Gaming GeForce RTX 4060 Ti OC
- After narrowing your selection, Please check the entire PCB picture to ensure compatibility. If you have any questions, don't hesitate to contact support for confirmation.
- Compatibility based on these circuit board designs only
- Fittings: G 1/4in. Thread
Parts Included
- 1x Full Coverage GPU Water Block
- 1x Backplate
- 2x Stop Fitting
- 1x Mounting Hardware
- Thermal grease
- 1x 5v A-RGB (RBW) Light
- (Warning: Addressable RGB (RBW) is 5V and is ONLY compatible with Addressable RGB (RBW) components. RGB is 12V and is ONLY compatible with RGB components. Mix and match will NOT work and will cause damage.
Warnings
This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item. The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
Not responsible for any damage caused by or when using this product. Please use it at your own risk.
This full coverage block directly cools the video cards core (GPU), graphics memory (RAM), and voltage regulator modules (VRM). By directly cooling these components, you can achieve great temperatures along with the ability to reach higher overclocks or extend the overall lifespan of your card by running at below factory temps.
The block is constructed of high-purity copper that is nickel electroplated to prevent oxidation. A high-flow design is used to allow multiple blocks to run in series. Top and bottom ports can be used to configure parallel or serial designs in multi-block setups.
Specifications
- Block Material: Nickel Electroplated High Purity Copper / Acrylic
- Backplate Material: Black Anodized Aluminum (not in contact with coolant)
Compatibility
- (Including but not limited to the following models)
- Compatible with ASUS ROG-STRIX GeForce RTX 4070 Ti-O12G-GAMING
- Please check over the entire PCB picture after narrowing your selection to ensure compatibility. If you have any questions, please contact support for confirmation.
- Compatibility based on these circuit board designs only
- Fittings: G 1/4in. Thread
Parts Included
- 1x Full Coverage GPU Water Block
- 1x Backplate
- 2x Stop Fitting
- 1x Mounting Hardware
- Thermal grease
- 1x 5v A-RGB (RBW) Light
- (Warning: Addressable RGB (RBW) is 5V and is ONLY compatible with Addressable RGB (RBW) components. RGB is 12V and is ONLY compatible with RGB components. Mix and match will NOT work and will cause damage.
Warnings
This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item. The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
Not responsible for any damage caused by or when using this product. Please use it at your own risk.
This full coverage block directly cools the video card core (GPU), graphics memory (RAM), and voltage regulator modules (VRM). By directly cooling these components, you can achieve great temperatures and reach higher overclocks or extend the overall lifespan of your card by running at below-factory temperatures.
The block is constructed of high-purity copper that is nickel electroplated to prevent oxidation. A high-flow design is used to allow multiple blocks to run in series. Top and bottom ports can be used to configure parallel or serial designs in multi-block setups.
Compatibility
- Compatible withΒ ASUS TUF Gaming GeForce RTX 4070 Ti SUPER BTF White OC Edition 16GB, ASUS TUF GeForce RTX 4070 Ti-12G-GAMING,ASUS TUF GAMING GeForce RTX 4070 Ti SUPER,ASUS TUF Gaming GeForce RTX 4070 OC,ASUS GeForce RTX 4070 Dual, ASUS TUF Gaming GeForce RTX 4070 SUPER OC,ASUS GeForce RTX 4070 SUPER Dual
- After narrowing your selection, Please check the entire PCB picture to ensure compatibility. If you have any questions, don't hesitate to contact support for confirmation.
- Compatibility based on these circuit board designs only
- Fittings: G 1/4in. Thread
Parts Included
- 1x Full Coverage GPU Water Block
- 1x Backplate
- 2x Stop Fittings
- 1x Mounting Hardware
- Thermal grease
- 1x 5v A-RGB (RBW) Light
- (Warning: Addressable RGB (RBW) is 5V and is ONLY compatible with Addressable RGB (RBW) components. RGB is 12V and is ONLY compatible with RGB components. Mix and match will NOT work and will cause damage.
Warnings
This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item. The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
Not responsible for any damage caused by or when using this product. Please use it at your own risk.
This full coverage block directly cools the video cards core (GPU), graphics memory (RAM), and voltage regulator modules (VRM). By directly cooling these components, you can achieve great temperatures along with the ability to reach higher overclocks or extend the overall lifespan of your card by running at below factory temps.
The block is constructed of high-purity copper that is nickel electroplated to prevent oxidation. A high-flow design is used to allow multiple blocks to run in series. Top and bottom ports can be used to configure parallel or serial designs in multi-block setups.
Specifications
- Block Material: Nickel Electroplated High Purity Copper / Acrylic
- Backplate Material: Black Anodized Aluminum (not in contact with coolant)
Compatibility
- (Including but not limited to the following models)
- Compatible with ASUS TUF Gaming GeForce RTX 4080, ASUS ROG Strix GeForce RTX 4080
- Please check over the entire PCB picture after narrowing your selection to ensure compatibility. If you have any questions, please contact support for confirmation.
- Compatibility based on these circuit board designs only
- Fittings: G 1/4in. Thread
Parts Included
- 1x Full Coverage GPU Water Block
- 1x Backplate
- 2x Stop Fitting
- 1x Mounting Hardware
- Thermal grease
- 1x 5v A-RGB (RBW) Light
- (Warning: Addressable RGB (RBW) is 5V and is ONLY compatible with Addressable RGB (RBW) components. RGB is 12V and is ONLY compatible with RGB components. Mix and match will NOT work and will cause damage.
Warnings
This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item. The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
Not responsible for any damage caused by or when using this product. Please use it at your own risk.
This full coverage block directly cools the video cards core (GPU), graphics memory (RAM), and voltage regulator modules (VRM). By directly cooling these components, you can achieve great temperatures along with the ability to reach higher overclocks or extend the overall lifespan of your card by running at below factory temps.
The block is constructed of high-purity copper that is nickel electroplated to prevent oxidation. A high-flow design is used to allow multiple blocks to run in series. Top and bottom ports can be used to configure parallel or serial designs in multi-block setups.
Specifications
- Block Material: Nickel Electroplated High Purity Copper / Acrylic
- Backplate Material: Black Anodized Aluminum (not in contact with coolant)
Compatibility
- (Including but not limited to the following models)
- Compatible withΒ ASUS ROG Strix GeForce RTX 4090,Β ASUS TUF Gaming GeForce RTX 4090
- Please check over the entire PCB picture after narrowing your selection to ensure compatibility. If you have any questions, please contact support for confirmation.
- Compatibility based on these circuit board designs only
- Fittings: G 1/4in. Thread
Parts Included
- 1x Full Coverage GPU Water Block
- 1x Backplate
- 2x Stop Fitting
- 1x Mounting Hardware
- Thermal grease
- 1x 5v A-RGB (RBW) Light
- (Warning: Addressable RGB (RBW) is 5V and is ONLY compatible with Addressable RGB (RBW) components. RGB is 12V and is ONLY compatible with RGB components. Mix and match will NOT work and will cause damage.
Warnings
This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item. The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
Not responsible for any damage caused by or when using this product. Please use it at your own risk.
BYKSKI Geforce RTX 5080 TUF Gaming GPU waterblock incl. backplate
Suitable for:
- ASUS TUF Gaming GeForce RTX 5080, 16384 MB GDDR7
- ASUS TUF Gaming GeForce RTX 5080 OC Edition, 16384 MB GDDR7
- ASUS TUF Gaming GeForce RTX 5070 Ti OC Edition 16GB
- ASUS TUF Gaming GeForce RTX 5070 Ti Edition 16GB
Material: Copper (nickel-plated), acrylic
Connections: G1/4
Manufacturer: Bykski
Part number: N-AS5080TUF-X
LED: Yes, 5v addressable
Β
Contains:
1x Full Cover GPU Block
1x backplate
2x blanking plugs
1x mounting material
1x thermal pads
1x manual
1x 5v RBW LED-Strip
The block is constructed of high-purity copper that is nickel electroplated to prevent oxidation. A high-flow design is used to allow multiple blocks to run in series. Top and bottom ports can be used to configure parallel or serial designs in multi-block setups.
Specifications:
Backplate material: black anodized aluminum (not in contact with coolant)
Compatibility:
ROG ASTRAL RTX 5090 O32G GAMING
Compatibility based on this(these) PCB designs only.
Inlet/outlet port size: G1/4" thread.
Parts Included:
1x Backplate
2x Plug fitting
1x Installation screwdriver
1x Lighting sync cable
1x Bykski thermal pads (set)
Warnings:
RGB is 12V 4pin lighting system, and is ONLY compatible with 12V components.
Mix and match will NOT work and will cause damage.
2. This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
3. The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal pad. In the middle part of product gallery images, there will be a picture description/display where the thermal pad should be placed. Installing pads on other components can lead to improper contact and poor performance.
4. Not responsible for any damage caused by or when using this product. Please use it at your own risk.
5. About [Extra option] - "Additional light controller"
If you do not intend/unavailable to sync lighting to the motherboard, you can choose this option to make lighting work normally.
*This controller can also be used as a hub (up to 4) at the same time for Bykski's same lighting system.
The Bykski Distro or Distribution Plates provide a distinct and innovative way to enhance your loop's appearance. These plates are customized to fit your specific case, creating a sleek and parallel look. Moreover, they can come equipped with an OPTIONAL inline pump, allowing you to power your entire loop from the centerpiece.
The Distro Plate is built using PMMA material, featuring G 1/4 threads, and is designed to be compatible with the Lian Li O11 Dynamic XL case. It works well with Aluminum and Non-Aluminum loops and is engineered to support radiators up to 30mm thick or less.
In addition to the Distro Plate itself, the package includes mounting hardware, an A-RGB (RBW) LED strip, and the option of including a DDC pump with armor, a DDC pump with LCD, or no pump at all. Bykski Distro Plates are an excellent option for those looking for a clean, visually appealing water-cooling solution that provides high-quality performance.
Specifications - Distro Plate
- Material: PMMA
- Thread: G 1/4
Compatibility
- Compatible with Lian Li O11 Dynamic XL case
- Loop: Aluminum or Non-Aluminum
- Radiator: Designed for 30mm thick or less
Included Parts
- 1x Distro plate
- Mounting Hardware
- A-RGB (RBW) LED Strip
- Optional DDC pump with armor, DDC pump with LCD, orΒ No Pump Included
Specifications -Β Optional DDC
- Heatsink Material: Aluminum
- Power: Standard 4-pin power connector and a PWM 4-Pin header
- Voltage Range: 10V - 15V DC
- MTBF (Mean Time Between Failure): 50,000 hours equivalent to 5 years of lifetime
- Maximum discharge:~ 132 GPH (600 LPH)
- Max RPM:5000
- Dimensions:62 x 62 x 58mm
- The performance will vary based on the cooling loop dynamic
Warnings
This block is designed specifically for this case. Depending on the motherboard, blocks, fittings used, and layout, the connecting tubing may not appear as pictured (perfectly horizontal). Not responsible for any hardware damage. Use at your own risk.
The Bykski Distro or Distribution Plates provide a distinct and innovative way to enhance your loop's appearance. These plates are customized to fit your specific case, creating a sleek and parallel look. Moreover, they can come equipped with an OPTIONAL inline pump, allowing you to power your entire loop from the centerpiece.
The Distro Plate is built using PMMA material, featuring G 1/4 threads, and is designed to be compatible with the PHANTEKS NV5s case. It is engineered to support radiators up to 30mm thick or less.
In addition to the Distro Plate itself, the package includes mounting hardware, an A-RGB (RBW) LED strip, and the option of including a DDC pump with armor, a DDC pump with LCD, or no pump at all. Bykski Distro Plates are an excellent option for those looking for a clean, visually appealing water-cooling solution that provides high-quality performance.
Specifications - Distro Plate
- Material: PMMA
- Thread: G 1/4
Compatibility
- Compatible with PHANTEKS NV5s case
- Radiator: Designed for 30mm thick or less
Included Parts
- 1x Distro plate
- Mounting Hardware
- A-RGB (RBW) LED Strip
- Optional DDC pump with armor, DDC pump with LCD, orΒ No Pump Included
Specifications -Β Optional DDC
- Heatsink Material: Aluminum
- Power: Standard 4-pin power connector and a PWM 4-Pin header
- Voltage Range: 10V - 15V DC
- MTBF (Mean Time Between Failure): 50,000 hours equivalent to 5 years of lifetime
- Maximum discharge:~ 132 GPH (600 LPH)
- Max RPM:5000
- Dimensions:62 x 62 x 58mm
- The performance will vary based on the cooling loop dynamic
Warnings
This distro is designed specifically for this case. Depending on the motherboard, blocks, fittings used, and layout, the connecting tubing may not appear as pictured (perfectly horizontal). Not responsible for any hardware damage. Use at your own risk.
The Bykski Distro or Distribution Plates provide a distinct and innovative way to enhance your loop's appearance. These plates are customized to fit your specific case, creating a sleek and parallel look. Moreover, they can come equipped with an OPTIONAL inline pump, allowing you to power your entire loop from the centerpiece.
The Distro Plate is built using PMMA material, featuring G 1/4 threads, and is designed to be compatible with the PHANTEKS-NV7 case. It works well with Aluminum and Non-Aluminum loops and is engineered to support radiators up to 30mm thick or less.
In addition to the Distro Plate itself, the package includes mounting hardware, an A-RGB (RBW) LED strip, and the option of including a DDC pump with armor, a DDC pump with LCD, or no pump at all. Bykski Distro Plates are an excellent option for those looking for a clean, visually appealing water-cooling solution that provides high-quality performance.
Specifications - Distro Plate
- Material: PMMA
- Thread: G 1/4
Compatibility
- Compatible with PHANTEKS-NV7 case
- Loop: Aluminum or Non-Aluminum
- Radiator: Designed for 30mm thick or less
Included Parts
- 1x Distro plate
- Mounting Hardware
- A-RGB (RBW) LED Strip
- Optional DDC pump with armor, DDC pump with LCD, orΒ No Pump Included
Specifications -Β Optional DDC
- Heatsink Material: Aluminum
- Power: Standard 4-pin power connector and a PWM 4-Pin header
- Voltage Range: 10V - 15V DC
- MTBF (Mean Time Between Failure): 50,000 hours equivalent to 5 years of lifetime
- Maximum discharge:~ 132 GPH (600 LPH)
- Max RPM:5000
- Dimensions:62 x 62 x 58mm
- The performance will vary based on the cooling loop dynamic
Warnings
This distro is designed specifically for this case. Depending on the motherboard, blocks, fittings used, and layout, the connecting tubing may not appear as pictured (perfectly horizontal). Not responsible for any hardware damage. Use at your own risk.
- 
AMD Ryzen 7 7800X3D β 8-core processor with 3D V-Cache for outstanding gaming efficiency and performance. 
- 
ASUS ROG Strix B850-I Gaming Wi-Fi 7 β Compact ITX motherboard with PCIe 5.0, Wi-Fi 7, and strong connectivity. 
- 
G.Skill Trident Z5 Neo RGB 32GB (2x16) DDR5 6000 CL32 β High-speed DDR5 with tight timings and customizable RGB lighting. 
- 
Samsung 990 EVO Plus 2TB Gen4 NVMe M.2 (C:) β Fast SSD with ample storage for OS, games, and applications. 
- 
Phanteks AMP GH 850W 80 Plus Gold ATX 3.1 PCIe 5.1, Black β Reliable PSU with Gold efficiency and PCIe 5.1 support. 
- 
XFX Mercury Radeon RX 9070 XT Magnetic Air OC 16GB β High-performance AMD GPU for smooth 1440p and strong 4K gaming. 
- 
Thermaltake Core P1 β Open-frame ITX case showcasing components with unique wall-mount or desktop flexibility. 
- 
InWin Lynx LN120 ARGB [3], Black β Premium ARGB fans with efficient cooling and sleek design. 
 
              
             
       
       
       
       
       
       
       
       
       
       
      